VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit shelf look: pre-order guide
starter vape kits · distributors

Starter Vape Kit shelf look: pre-order guide

Starter Vape Kit is a specification decision before it is a price decision. Get the resistance, the capacity and the packaging right and the price conversation becomes short. Get them wrong and no discount will rescue the order.

Published 01 January 2026  ·  VapeWholesaleHub  ·  Reading time 8 min

Starter Vape Kit shelf look configuration from a production run, photographed before packing.
Starter Vape Kit shelf look configuration from a production run, photographed before packing.
Packaging proof for the export market, approved before the run.
Packaging proof for the export market, approved before the run.

Reading a quotation properly

Buyers come to us for starter vape kit after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for distributors.

The cheapest way to lower your cost per unit is usually to remove a SKU, not to negotiate a discount. Fewer lines means larger runs, fewer changeovers and a better price at the same quality.

We publish a realistic band of 2.70 to 8.25 per unit for standard configurations at 300 units. Below that band you are buying a lighter specification; above it you are paying for finish, packaging or a smaller run.

After-sales, replacements and reorders

Returns are handled as data, not as complaints. Every reported failure is logged by mode and by batch, and the pattern is reviewed monthly with the factory.

The replacement policy is deliberately simple: report within seven days of delivery with photos and the batch code, and we replace or credit at the next shipment. We do not argue about a defect we can see in a photograph.

For distributors, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Simple habits that lift velocity

Photography matters for online listings. Shoot on a neutral background with the device at a slight angle, show the pack alongside the unit, and keep the same framing across the range so the grid reads as a family.

Staff knowledge converts better than any poster. If your team can explain the difference between two coils in one sentence, the step-up SKU sells itself.

  • Mixed SKU cartons to spread first-order risk
  • Seven-day defect reporting with replace-or-credit
  • Standing reorder schedule with a fixed cut-off
  • Batch codes traceable from carton back to production date
  • Specification locked in writing before production starts
  • Private label files archived for future rebrands

What we test before a carton is sealed

12 separate checks run before a carton is sealed: electrical, mechanical, leak, finish and packaging. Anything outside tolerance is quarantined the same day and reported to you, rather than shipped with a hope and a discount.

A 0.5 percent defect rate sounds excellent until it lands on a 600 unit order and you are handling three returns in a week. We quote realistic rates per category and we credit in advance for the known failure modes.

Specification summary

Typical specification for this category
Battery800 mAh
Pod capacity3.0 ml
Coil resistance0.8 ohm
IncludedDevice, 2 pods, cable
ChargingUSB-C 5V/1A
PackagingRetail box
Minimum order100 units per SKU, mixed cartons allowed
Lead time18 working days after artwork approval

We would rather lose an order at quotation stage than explain a mismatch after delivery, which is why the specification conversation comes before the price conversation.

Frequently asked

How long does production take?

Around 22 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

What is the minimum order for starter vape kit?

Standard configurations start at 300 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 800 units because of setup time on the line.

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us