VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit return and replacement — a guide
starter vape kits · distributors

Starter Vape Kit return and replacement — a guide

We ship starter vape kits to distributors, chain buyers and independent shops. What follows is the material we normally cover in a first conversation: what we hold in stock, how we test it, how it ships, and what happens when a carton arrives damaged.

Published 04 September 2026  ·  VapeWholesaleHub  ·  Reading time 9 min

Finish and assembly detail checked against the approved reference sample.
Finish and assembly detail checked against the approved reference sample.
Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.
Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.

Where defects actually come from

Starter Vape Kit sits in a crowded price band, and the cheapest quote on the sheet is rarely the cheapest unit on your shelf. Everything below is built around reorder rate, defect rate and cash conversion rather than headline unit price.

We photograph the packing station during production for volume orders. It is a small thing, but it settles most arguments about what was actually in the carton before it was sealed.

Flavour drift between batches is the quiet killer of repeat orders. We retain a sealed reference sample from every run so a complaint six weeks later can be compared against what actually left the building.

Paperwork, labelling and market rules

Age verification is not only a website problem. Retail packaging, shelf placement and staff scripting all carry compliance weight, and auditors increasingly ask for evidence of all three.

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

For distributors, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Sell-through notes for the shop floor

Shelf position decides velocity as much as price. Keep starter vape kits at eye level, one facing per SKU, and rotate the trial line every quarter so the display keeps earning attention.

Photography matters for online listings. Shoot on a neutral background with the device at a slight angle, show the pack alongside the unit, and keep the same framing across the range so the grid reads as a family.

  • Consolidated or split shipping, quoted both ways
  • Artwork proof plus physical dummy for custom packaging
  • Specification locked in writing before production starts
  • Seven-day defect reporting with replace-or-credit
  • Standing reorder schedule with a fixed cut-off
  • Mixed SKU cartons to spread first-order risk

Lead times, freight and landed cost

We ship from Shenzhen and Guangzhou: air express for samples and part loads, sea freight for volume. Typical production lead time is 28 working days after artwork approval, plus transit. We quote both routes so you can see the trade-off instead of guessing at it.

Damage in transit is nearly always a packing decision, not bad luck. Double-walled cartons, internal dividers and a drop-tested configuration cost a little more and save the argument at the other end.

Specification summary

Typical specification for this category
Battery800 mAh
Pod capacity2.0 ml
Coil resistance1.0 ohm
IncludedDevice, 2 pods, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order50 units per SKU, mixed cartons allowed
Lead time30 working days after artwork approval

None of this is complicated. It is just written down, which is more than most buyers get before they wire a deposit.

Frequently asked

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

How long does production take?

Around 28 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

What is the minimum order for starter vape kit?

Standard configurations start at 60 units per SKU, with mixed SKUs allowed inside the same carton. Custom colours, custom packaging or a private label run usually start at 240 units because of setup time on the line.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us