VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit flavour range checklist guide
starter vape kits · distributors

Starter Vape Kit flavour range checklist guide

Starter Vape Kit sits in a crowded price band, and the cheapest quote on the sheet is rarely the cheapest unit on your shelf. Everything below is built around reorder rate, defect rate and cash conversion rather than headline unit price.

Published 25 January 2026  ·  VapeWholesaleHub  ·  Reading time 7 min

Unit from the retained reference sample held against this order number.
Unit from the retained reference sample held against this order number.
Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.

Where defects actually come from

A starter vape kit programme only works when three numbers agree: your shelf price, your reorder cycle and your defect tolerance. Change one and the plan moves. We build assortments around those three and we say so up front rather than after the invoice.

Every batch is pulled from running production, not from a display shelf. We check draw resistance, airflow balance, charge behaviour, leak performance after a temperature shift, finish quality and carton integrity, and we keep the pull records against the order number.

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

After-sales, replacements and reorders

For private label accounts we hold the artwork files and the approval record. Rebranding a line eighteen months later is then a file update instead of a redesign.

Returns are handled as data, not as complaints. Every reported failure is logged by mode and by batch, and the pattern is reviewed monthly with the factory.

For distributors, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Choosing the core line

A practical starting order for distributors is 240 units across two or three SKUs, not 240 units of one. That spreads the risk, gives your staff something to compare, and still hits the first price break.

Factory capacity matters more than factory size. A line that can hold a tolerance across 5,000 units is worth more than a showroom that can produce 50,000 on paper. We qualify capacity by running a repeat order and measuring the drift.

  • Cartons drop-tested and pallet-counted for clean freight
  • Document pack prepared per destination market
  • Standing reorder schedule with a fixed cut-off
  • Batch codes traceable from carton back to production date
  • Artwork proof plus physical dummy for custom packaging
  • Specification locked in writing before production starts

Unit price versus landed cost

Freight is quoted separately and honestly. Bundling it into the unit price looks tidy and hides the one line that changes most often between shipments.

The cheapest way to lower your cost per unit is usually to remove a SKU, not to negotiate a discount. Fewer lines means larger runs, fewer changeovers and a better price at the same quality.

Specification summary

Typical specification for this category
Battery500 mAh
Pod capacity2.5 ml
Coil resistance1.2 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingRetail box
Minimum order200 units per SKU, mixed cartons allowed
Lead time22 working days after artwork approval

The detail above is what we hold ourselves to on every shipment, including the small ones. It is also the list we will walk through with you before the first order.

Frequently asked

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

What documents come with a shipment?

Commercial invoice, packing list, and the certificate pack for your market: test reports, declaration of conformity and safety data sheets. We send scans before dispatch so your broker can pre-clear the file.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us