VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  How to source Starter Vape Kit quality agreement timeline
starter vape kits · distributors

How to source Starter Vape Kit quality agreement timeline

We work with distributors who order between a few hundred and a few thousand units at a time, and we treat both ends the same way: a written specification, a sample you approve, and a production run that matches the sample.

Published 19 June 2026  ·  VapeWholesaleHub  ·  Reading time 8 min

Finish and assembly detail checked against the approved reference sample.
Finish and assembly detail checked against the approved reference sample.
Bulk packing station during the run for a distributors order.
Bulk packing station during the run for a distributors order.

Where the margin really sits

Buyers come to us for starter vape kit after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for distributors.

The cheapest way to lower your cost per unit is usually to remove a SKU, not to negotiate a discount. Fewer lines means larger runs, fewer changeovers and a better price at the same quality.

Payment terms for new accounts are normally a deposit with the balance against the bill of lading. Established buyers on a repeat schedule can move to terms after three clean shipments.

The checks behind every shipment

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

Battery safety is not a marketing line. Cells are matched by capacity and internal resistance before assembly, charging boards are checked for cut-off voltage, and any unit that fails the cut-off test never reaches packing.

For distributors, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

How we structure a first order

A practical starting order for distributors is 500 units across two or three SKUs, not 500 units of one. That spreads the risk, gives your staff something to compare, and still hits the first price break.

Factory capacity matters more than factory size. A line that can hold a tolerance across 5,000 units is worth more than a showroom that can produce 50,000 on paper. We qualify capacity by running a repeat order and measuring the drift.

  • Batch codes traceable from carton back to production date
  • Consolidated or split shipping, quoted both ways
  • Named account contact who has handled the product
  • Mixed SKU cartons to spread first-order risk
  • Document pack prepared per destination market
  • Reference sample retained from every batch

What happens when something goes wrong

The replacement policy is deliberately simple: report within seven days of delivery with photos and the batch code, and we replace or credit at the next shipment. We do not argue about a defect we can see in a photograph.

Reorders are the real test of a supplier. If the second shipment does not match the first, the relationship is over regardless of price, so we treat the reorder as the actual deliverable.

Specification summary

Typical specification for this category
Battery800 mAh
Pod capacity2.5 ml
Coil resistance1.2 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingRetail box
Minimum order100 units per SKU, mixed cartons allowed
Lead time22 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

How long does production take?

Around 25 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

How do you handle repeat orders?

The specification is held on file against your account, so a reorder is a reference rather than a new brief. We recommend a standing schedule with a fixed weekly cut-off so stock lands before the shelf empties.

Can you ship to multiple locations?

Yes. Split shipments are quoted separately because consolidation and splitting price differently. Tell us the destination list at quotation stage and we will show both options.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us